Denim Manufacturing Process

For manufacturing Denim and Grey Fabric, the process is same up to the level of weaving, but in case of Denim Fabric, dyeing is done at the stage of sizing where as for
Grey Fabric it depends upon the finished product. The details of each process are given below:-

1.   Fabric Weaving 

a. Grey Yarn on Cones

Normally yarns received for weaving in cone forms are either from ring spinning or from open end spinning in single or double fold as required. For weaving, yarn used is categorised into:

• Warp yarn 
• Weft yarn

Normally for Weaving, yarn used as warp should be sufficiently strong to withstand stress and strains exerted during weaving operations. Hence they are having Count Strength Product(CSP) and further sized to increase its strength. The weft yarn is directly used on weaving machines and in some cases, if required, is rewound also so as to enhance its performance in weaving.



b.  Warping on Sectional/ Direct Warping
The warp yarn is required to be fed into a sheet form to the weaving machines. At warping, the individual cones are put into the creel (the number of cones depends upon fabric construction) and yarn from individual cones is pulled together in sheet form, wound on a barrel called warping beams (for Direct warping) or on weaving beams (for Sectional Warping). Normally if warp sheet is with patterns of different coloured yarns it is processed on sectional warping machine. 

c. Sizing of yarn in Set/ Beam to Beam Position
The object of Sizing is to improve the strength of yarn by chemically binding the fibres with each other and also improve upon its friction resistance capacity by chemically coating the surface of yarn/fibres. Further, number of threads in warpers beam sheet is very less against number of threads required in whole width of fabric. Hence multiplication of sheets by drawing yarns together from many warp beams and again making one sheet is also performed on sizing machine. On sizing, normally, 8-12 % size material on warp thread is applied. This improvement in strength and frictional resistance characteristic of warp yarn is essential because during weaving, yarn has to undergo severe strain & stress as well as frictional operations.

d. Drawing–in
Weaving is basically interlacement of two sets i.e. warp and weft threads in desired sequence and pattern. To obtain this interlacement, warp yarn sheet is bifurcated & opened in the form of two layers/ sheet and weft thread is inserted between so opened two warp sheets. This operation is called shedding. to perform shedding the warp yarn needs to be passed through heald eyes of the heald shafts, this operation is called as drawing-in.

e. Beam Gaiting or Knotting on Loom
The drawn weavers beams are fixed on weaving machines, threads are tied and heald shafts are coupled. This operation is called Beam Gaiting. If undrawn warp threads are directly knotted to the threads of finished beams, it is called Knotting. These operations are essential because normally weavers beam can carry only certain length of warp sheet on it and when so woven, whole length
is converted to the fabric by weaving machine. Further warp length is required to be fed which can be done by knotting or gaiting other beams on weaving machine.

f. Weaving 
As stated earlier, weaving is interlacing two sets of yarn and making fabric. One set is called warp thread which is in sheet form, the other one is called weft thread which is inserted between two layers of warp sheet by means of a suitable carrier i.e. Shuttle, Projectile, Rapier, Air current, Water current, etc. Depending upon the type of the weaving machines. The different types of technologies available for weaving machines are briefly explained as below:

•  Conventional Shuttle Weaving System by Ordinary Looms or Automatic Looms.
• Shuttle less Weaving System by Airjet /Waterjet/Rapier/Projectile Shuttle loom is a conventional Technology with much less production on account of slow speed and excessive wear and tear of machinery. This shuttle loom technology has now become obsolete. Denim is woven through Shuttleless Weaving System by using 96 ZAX-e Type Tsodakoma Corporation’s Airjet looms or rapier looms or projectile looms.

Airjet Looms
These types of looms adopt the latest development in Weaving Technology where weft insertion is done with the help of compressed air. A very high weft insertion rate up to 1800 metre per minute is achieved. Compared to rapier and projectile looms, these looms are less versatile but are economical and are used in mass textile production unit like denim.